Project

General

Profile

K40-III » History » Version 2

DeanoC, 2013-03-10 19:35

1 1 darrenp
{{>toc}}
2
3
4
h1. K40-III
5
6
This is a cheap Chinese built laser that comes with a couple of different control boards, and some proprietary software.
7
8
h2. Control board - 6c6879
9
10
This board uses a flat ribbon cable for X axis motor and both X and Y limit sensors, a 4 pin JST connector for the Y axis motor, and a 6 pin connector for power and laser control.
11
12
!controller.jpg!
13
14
h3. Connectors
15
16
h4. Y stepper cable
17
18
|Color|Signal|Connect to|
19
|RED|XA+|J18.2 A|
20
|BLUE|XA-|J18.3 A|
21
|YELLOW|XB+|J18.4 B|
22
|WHITE|XB-|J18.5 B|
23
24
!DSC_3647.jpg!
25
26
h4. Flatcable for X stepper and endstops
27
28
|_.Pin|_.Signal|_.Connect to|
29
|PIN12|XA-|J24.1 A|
30
|PIN11|XA+|J24.2 A|
31
|PIN10|XB-|J34.3 B|
32
|PIN9|XB+|J34.4 B|
33
|PIN6|COMMON|J34.4 GND|
34
|PIN5|XHOME|J34.2 XHOME|
35
|PIN4|YHOME|J34.3 YHOME|
36
|PIN3|+5V|J34.1 Vsensor|
37
38
!783px-HPC-flat-cable-pinning.jpg!
39
40
h4. Power and Laser
41
42
|_.Pin|_.Signal|_.Connect to|
43
|1|Not Connected||
44
|2|Laser||
45
|3|5V||
46
|4|Not Connected||
47
|5|24V||
48
|6|GND||
49
50
h2. PSU 
51
52
!PSU.jpg!
53
54
The PSU has 4 connectors.
55
56
1. K+/K- - Laser Test button
57
2. G/IN/5V - Power control potentiometer
58
3. D+/D- - Laser enable/safety interlock
59
4. 24V/G/5V/L - Power to controller board
60
61 2 DeanoC
Our K40-III had a completely different power system. Also the Moshidraw boardand cabling we replaced didn't use the 5V rail that PSU generated, but you can (if you don't want to add the wire) use the 7805 to drop the 24V line to 5V.
62
63
Here are some photos of this PSU
64
!laser_psu_largebrd.jpg!
65
!laser_psu_smallbrd.jpg!
66
67
68 1 darrenp
h2. Hooking it up
69
70
[[K40-III 6c6879 Connections to Laos board]]
71
[[K40-III Material Settings]]
72
[[K40-III Improvements]]
73
74
h2. Other Notes
75
76
This machine is not what you'd call up to standards. Please bear in mind that there is no:
77
78
* Lid sensor
79
* Sensor to see if water is flowing
80
* Laser temperature sensor
81
* Cutting area temperature sensor to monitor for fire
82
* Extractor sensor to make sure fumes are being extracted.
83
84
Buy and operate this machine at your own risk. It is cheap, but you get what you pay for. In the [[K40-III Improvements]] will be some circuits to overcome some of these issues.