Project

General

Profile

LAOS I2C Panel v04 » History » Version 16

jaap, 2015-05-23 13:52

1 2 jaap
h1. LAOS I2C Panel v0.4
2 1 jaap
3
{{>toc}}
4
5 3 jaap
!>display-rev0.4.jpg!
6 1 jaap
7
h2. Basics
8
9
We designed a panel with a 2x16 LCD, 4 buttons and a joystick. The heart of the panel is a ATMEGA168-20PU running a small Arduino program. The panel uses I2C communication to the MBED board, but there is also a connection for a standard USB->TTL cable. You can use such a cable to upgrade the program in the Arduino chip.
10
All the source files of this project are available in the i2c panel project on Github: https://github.com/LaosLaser/AddOns
11
12
h2. Functionality
13
14
The user interface functionality is not implemented in this board, but in the program on the MBED. The on board ATMEGA with Arduino code only receives data for displaying on the screen and sends key press codes via I2C, basically this works as a tiny terminal. The functionality as stated here is just to show what the main LaOS controller board uses it for.
15
16
While no job is running:
17
18
* Manual focus, using up and down buttons (for some machines this will mean that the Z-axis is moving, others will move the lens-holder up and down)
19
* Moving the head to a specific location (jog in the X and Y axis)
20
* Select the current location and make that the origin (x=0, y=0, z=0)
21
* Select print job
22
23
While a job is printing:
24
25
* Pause current job
26
* Resume paused job
27
* Cancel current job
28
29
h2. Electronics
30
31
We designed our own board and software (Arduino based) to connect the display board to the mainboard (via I2C interface). The schematics (in KiCAD) are located ["here":https://github.com/LaosLaser/AddOns]. 
32
33
Most important parts:
34
35 5 jaap
"Full part list is available in GIT":https://github.com/LaosLaser/AddOns/blob/master/i2c-panel/pcb-0.4/bom.ods
36 1 jaap
37
* 16x2 LCD Display, RS stocknummer 532-6408
38
* ATMega168P-20PU, RS stocknummer 696-2430
39
* 4 Pushbuttons
40
* 1 Joystick button
41
* and of course, the PCB
42
43
!173px-Panel-rev0.3front.jpg!
44
45
h3. Bill of Materials
46
47
|_.Number|_.Component|_.RS Part No.|_.RS Price|_.Farnell Part No.|_.Farnell Price|_.Comment|
48 12 jaap
|1|LCD display, 16x2 characters|532-6408 / 720-0207|€ 5,50| | ||
49 1 jaap
|1|ATMega168P-20PU|738-0375|€ 5,22|1636933|€ 4,81||
50 14 jaap
|1|ATMega328P-20PU|-|-|-|-|either 168 or 328, not both|
51 1 jaap
|4|Thru hole tactileswitch12x12x7.3mm|378-6763|€ 0,46| | ||
52
|1|PCB Stick switch, 4 dir + centre push|516-316|€ 2,46|1435775|€ 2,47||
53
|1|Ceramic resonator THT CSTLS 16.00MHz|526-6154|€ 0,56|1448129|€ 0,46||
54
|1|28way low profile DIL socket,0.3in pitch|801-768|€ 0,24| | ||
55
|1|100uF capacitor|711-0703|€ 0,03| | ||
56
|2|100nF capacitor|721-5240|€ 0,07| | ||
57
|1|10K resistor|707-7745|€ 0,02| | ||
58 12 jaap
|1|36 way straight header,7mm top 3mm below|251-8632|€ 1,034|1824426|€ 0,92||
59 6 jaap
|2|BS270|| 1017689|€ 0,15||
60
|1|Kingstate KPEG242 buzzer| | |1502726|€ 2,03| |
61 1 jaap
|3|plastic buttoncap black|378-6943|€ 0,11| | ||
62
|1|plastic buttoncap red|378-6937|€ 0,11| | ||
63 16 jaap
|1|lasercut cardboard||||||
64 6 jaap
|1|PCB E218213| |€ 7,50| | |Available from LaOS (see "WebShop":http://tuxic.nl/webshop )|
65 1 jaap
66
h2. Mechanical construction
67
68
* PCB is positioned directly under the display
69
* I2C communication is through a 4-pin flatcable with pin-header
70
* A 6-pin (USB->TTL) connector is available for easy updates of the Arduino
71
* 4 standard pushbuttons
72
* 1 Joystick button (with 3D printed key cap)
73
74
The design files for a frontpanel and buttons can be found here: ["Frontplates":https://github.com/LaosLaser/AddOns/tree/master/i2c-panel/frontplates]
75 10 jaap
Peter Uitenhoven posted a Joystick thumb on Thingiverse: http://www.thingiverse.com/thing:87346
76 1 jaap
77
h2. Implementation
78
79 9 jaap
The Arduino software on the ATMEGA chip is "available on github":https://github.com/LaosLaser/AddOns/raw/master/i2c-panel/firmware/lasercutterpanelv0_4.ino
80 1 jaap
81
The electronics are based on "John Crouchley's ATTiny2313":http://john.crouchley.com/blog/archives/612 implementation. The Arduino (or Ottantotto) electronics come from "Edwin Dertien":http://wiki.edwindertien.nl/doku.php?id=boards:ottantotto:start#pin_description.
82
83
Relevant Arduino libraries:
84
85
* LCD driver: "http://www.arduino.cc/en/Reference/LiquidCrystal":http://www.arduino.cc/en/Reference/LiquidCrystal
86
* i2c: "http://www.arduino.cc/en/Reference/Wire":http://www.arduino.cc/en/Reference/Wire
87
* Keypad: "http://www.arduino.cc/playground/Code/Keypad":http://www.arduino.cc/playground/Code/Keypad
88
89 11 peteruithoven
I2C on the Mbed: "http://mbed.org/handbook/I2C":http://mbed.org/handbook/I2C "Have a look at this very enlightning drawing!":http://mbed.org/media/uploads/ColonelPewter/i2c_001004.gif
90 1 jaap
91
For debugging, you can use any PC with a home-made I2C adapter:
92
93
p(((. http://www.instructables.com/id/Worlds-Cheapest-I2C-I-Squared-C-Adapter/
94
http://www.paintyourdragon.com/?p=43
95
96
97
h2. Building your own
98
99
To make life easier, we sell premade PCB's and this panel as a kit. See the "WebShop":http://tuxic.nl/webshop.
100
101
The kit contains:
102
103
* PCB
104
* ATMEGA168-20PU, pre-programmed with the Arduino bootloader and this I2C program (so you can install it even if you do not own a USB->TTL cable).
105
* LCD
106
* other electronic parts
107
* Buttons
108
* I2C wire to motherboard
109
110
Parts it does not contain:
111
112
* Laser cut panel. You can make one on your laser, maybe? Probably you want one to fit into your machine, anyway. See below for the panel the MiniFabLab made for its HPC LS3020
113
* 3D Printed joystick button. When I design one I'm really proud of, I might include it.
114
115
Feel free to make the user interface panel yourself if you prefer. No need to buy stuff if you have an Arduino lying around with LCD and some buttons!
116
117
h2. Soldering
118
119 6 jaap
This board has parts on BOTH sides! The display and buttons go on one side, all the other electronic parts go on the other.
120
121
Non-display side: the side where it says "LAOS I2C rev 0.4".
122
* Start by soldering the  the socket for the Atmel IC, making sure the notch is on the same side as the one on the silkscreen legend. 
123
* Place the resistors. There is only one, that's why it's labeled R2
124
* Solder the two 100nF capacitors in U1 and U4.
125
* Solder the 100uF electrolytic capacitor with the plus (longer) wire in the hole with square solder pad (U2).
126
* Solder in the two BS270 in Q1 and Q4.
127
* Solder the 3 pin ceramic resonator (F1)
128
* Solder the piezzo buzzer (SP1).
129
* Place a 2-pin header in P3 and P7, a 4-pin header for I2C and a 6-pin header in P1 (TTL). Place two 3-pin headers in P4.
130 1 jaap
* Now take a 16-pin header and push it with the longer pin ends in the PCB from the bottom (solder) side of the board. The long pins will stick out on the top side of the board. The black plastic of the header in now on the bottom of the PCB. Measure with the display module to see if the pins are long enough to go just through the module. Solder the 16-pin header to the board on the TOP (component) side.
131
Front (display side):
132 16 jaap
* Place a strong piece of tape or (lasercut) cardboard on the bottom side of the board, covering the part of the board that will be under the display module, so that there cannot be any shortcircuit between the board and the display module. You can use electric shielding tape or gaffer tape.
133 1 jaap
* Solder the display module on the back side board, with the black strip of the 16-pin header in between.
134 6 jaap
* Solder the 4 buttons to the board (not the joystick yet!) with the buttons on the side of the display (solder side). 
135
* The joystick has a very small dent in the top metal layer. If you put the joystick in, this dent should be on the right side, where there is a small mark on the print. Solder it in.
136 1 jaap
137 8 jaap
Front side of the panel.
138 7 jaap
!display-rev0.4.jpg!
139 1 jaap
140 6 jaap
Back side of the panel.
141 7 jaap
!display-back-rev0.4.jpg!
142 1 jaap
 
143
144
h2. Software installation
145
146
h3. Installing a bootloader
147
148 14 jaap
These instructions are for ATMEGA168P-PU
149
<pre>
150
cd /opt/arduino-1.6.4/hardware/arduino/avr/bootloaders/atmega
151
avrdude -p m168p -c usbasp -F -U lock:w:0x3F:m -U efuse:w:0xF8:m -U hfuse:w:0xDE:m -U flash:w:ATmegaBOOT_168_diecimila.hex -U lfuse:w:0xff:m
152 15 jaap
</pre>
153 1 jaap
Error message while installing:
154
155
    avrdude: safemode: efuse changed! Was f8, and is now 0
156
Would you like this fuse to be changed back? [y/n]
157
158
Answer n !
159 14 jaap
160
and for the ATMEGA328P-PU
161
<pre>
162
<cd /opt/arduino-1.6.4/hardware/arduino/avr/bootloaders/optiboot
163
avrdude -p m328p -c usbasp -F -U lock:w:0x3F:m -U efuse:w:0x05:m -U hfuse:w:0xDE:m -U flash:w:optiboot_atmega328.hex -U lfuse:w:0xFF:m
164
</pre>
165 1 jaap
166
h3. Arduino Sketch
167
168
Use a USB=&gt;TTL cable to connect the board to your computer. Install "Arduino":http://www.arduino.cc software. Get "lasercutterpanelv0&#95;3.pde from GIT": https://github.com/LaosLaser/AddOns/raw/master/i2c-panel/firmware/lasercutterpanelv0_3.pde
169
170
To test your panel, change:
171
172
    #define DEBUG 0 
173
174
175
to
176
177
    #define DEBUG 1
178
179
180
Arduino settings: Board: Arduino NG or older with Atmega168
181
182
Upload the file to the board. This will give you a welcome text. After the text has disappeared, all buttons should show a number on the screen. The joystick should show 5 different values for each direction and middle push.
183
184
If it works, upload the code again with *DEBUG 0*. The panel is now ready to be connected to the mainboard.
185
186
h2. Control Panel on the HPC LS3020
187
188
189
To accomodate the display you can cut a replacement for the control panel. 
190
191
!greenpanel-bart.jpg!
192
193
The button laser switch was replaced by a toggle for better on/off reference. So the right serial test button could be omitted. Also the lighting switch was removed, now the light is always on. No modifications are required for the cabletree, just connect the wires from the removed switches. The air pump switch was kept as a compressor can be noisy. It is advised to use a shielded cable between the I2C panel and the board. A cutting file (.svg) of this panel is available on "miniFabLab":http://minifablab.nl/uploads/LaOS3020panel.svg.
194
195
196
h2. More
197 8 jaap
198
Previous version: https://redmine.laoslaser.org/projects/laos/wiki/LAOS_I2C_Panel_v03
199 1 jaap
200
For links on previous versions and to get started on designing your own display, see the [[Display-alternatives]] page.
201 13 jaap
202
Cable conn:  Preci-dip, RS: 702-0095