LAOS Mainboard v05minimal » History » Version 1
jaap, 2015-04-24 09:43
| 1 | 1 | jaap | h1. LAOS Mainboard v05 - minimal configuration for 2 axis |
|---|---|---|---|
| 2 | |||
| 3 | This page describes the building process of a minimal LaOS board for a 2-axis machine. |
||
| 4 | |||
| 5 | h3. Bill of Materials |
||
| 6 | |||
| 7 | |1||||Laos mainboard||||| |
||
| 8 | |3|C1, C3, C8|100nF|Decoupling capacitors for diverse parts|100nF Ceramic capacitor, 5.08mm pin spacing|2112751||721-5240|€ 0,07|niet: C2,C5| |
||
| 9 | |1|C7|22nF|Input decoupling for the 7805|22nF ceramic capacitor, 100nF is fine too|1141773||721-5268|€ 0,12|| |
||
| 10 | |1|C4|1000uF|Voltage buffer for the Pololu's, stabilization of Vmot|1000uF capacitor, 5.0mm pin spacing, 10mm diameter; voltage rating at least 1.6 to 2 times VMOT|1855170 (moq 5)|€ 0,65|520-1090|€ 1,31|| |
||
| 11 | |4|C6,C9,C10,C11|100uF|Voltage buffer for VCPU and Pololus|100uF capacitor, voltage rating at least 1.6 to 2 times VMOT|1902932||520-0996|€ 0,28| |
||
| 12 | |5|R10, R18, R19, R21, R22|10k|Pullup resistors for the optocoupler inputs and analog input|10 kOhm resistor|9339060||707-7745|€ 0,02| |
||
| 13 | |13|R12, R15, R17, R30, R2, R3, R4, R5, R23, R24, R26, R27, R33|1k|Diverse functions: current limiting resistors for the leds, bias resistors for the high current output transistors, voltage divider for the analog input|1kOhm resistor|9339051||707-7666|€ 0,02| |
||
| 14 | |4|R28, R29, R31, R32|330R|Current limiting resistors for the leds in the output optocouplers|330 Ohm resistor|9339418||707-7622|€ 0,02| |
||
| 15 | |1|R34|100R|Limiting/protection resistor for the microcontroller's analog input|100 Ohm resistor|9339043||707-7587|€ 0,02| |
||
| 16 | |2|R7, R8|2K2|Pullup resistors for the I2C bus|2.2kOhm resistor|9339302||707-7690|€ 0,02| |
||
| 17 | |1|J11|MBED NXP|The microcontroller that's the core of the board|mBed LPC1768 module|1761179|€ 49,73|703-9238|€ 49,53| |
||
| 18 | |1|J4|MAGJACK|Ethernet connector with magnetics|MAGJACK SI-60002-F|1137981|€ 6,27|741-8477|€ 4,38| |
||
| 19 | |1|J11|MBED NXP|Mbed Holder|TE Connectivity 2.54mm 40 Way 2 Row Straight PCB Socket Through Hole Socket Strip|9688862|€ 2,84|509-2925|€ 3,69| |
||
| 20 | |1|U2|Hirose DM1B-DSF-PEJ(82) or Molex 502774-0891|SD card holder|Micro SD SMD: Molex 502774-0891 Regular: Hirose DM1B-DSF-PEJ(82)|2064063 / 1764373|€ 2,65|685-0788 / 720-6072|€ 2,22| |
||
| 21 | |1|D1|LEDR|This led indicates that the stepper drivers are enabled.|Low cost 3mm red led|1045372||708-2753 |€ 0,09| |
||
| 22 | |1|D2|LEDY|This led indicates the presence of VMOT|Low cost 3mm yellow led|2080002||708-2769 |€ 0,11| |
||
| 23 | |1|D3|LEDG|This led indicates the presence of a 5V supply for the microcontroller|Low cost 3mm green led|1652494||708-2756 |€ 0,11| |
||
| 24 | |2|IC1, IC2|KB847|Quadruple optocoupler for the endstops/outputs|Kingbright KB847|2001656|€ 2,04|619-2026|| |
||
| 25 | |2|||Socket for optocouplers, 0.3inch wide, 16 pin||1077315|€ 2,17|402-771 |€ 0,18| |