Wiki » History » Version 52
Anonymous, 2012-07-16 17:55
| 1 | 32 | Anonymous | h1. LAOS Laser |
|---|---|---|---|
| 2 | 1 | jaap | |
| 3 | 32 | Anonymous | {{>toc}} |
| 4 | 1 | jaap | |
| 5 | 32 | Anonymous | !>LaOSLogo.png! |
| 6 | 1 | jaap | |
| 7 | 50 | Anonymous | This site is about an Open Source laser engraver/cutter controller system, both hardware and software. Further info can be found on the [[Rationale and background]] page. The site was created in 2010 by Jaap Vermaas and Peter Brier, and is now being taken further with the help of other [[Contributors]]. |
| 8 | 1 | jaap | |
| 9 | 49 | Anonymous | A laser cutter consists of several components, as described on [[How does a laser cutter work?|this page]] - this site focuses on units such as the [[HPC LS3020]], in combination with the LAOS electronics. For a full list, see the [[Laser Cutters|Supported lasers]] so far. The current electronics are [[LAOS Mainboard v0.3]] and [[LAOS I2C panel v0.3]] - older versions are listed on the [[Electronics]] page. |
| 10 | 1 | jaap | |
| 11 | 52 | Anonymous | > Tip # 1: for quick navigation, see the tabs at the top of each page on this site. |
| 12 | > Tip # 2: click on the section titles below for a list of all the pages related to that section. |
||
| 13 | 1 | jaap | |
| 14 | 46 | Anonymous | h2. [[HowTo's]] |
| 15 | 1 | jaap | |
| 16 | 39 | Anonymous | * [Figure out what you'll need and where to get it] |
| 17 | 41 | Anonymous | * [Prepare your laser cutter for use with LAOS] (including a first firing test) |
| 18 | 44 | Anonymous | * [Assemble the LAOS electronics boards] |
| 19 | 39 | Anonymous | * [Install firmware and verify proper operation] |
| 20 | 44 | Anonymous | * [[Connect the electronics and hook it up to your network]] |
| 21 | 41 | Anonymous | * [Install required software on your Windows, Mac, or Linux PC] |
| 22 | 47 | Anonymous | * [[Troubleshooting]] - [Where to get help] - [Contributing to this wiki] |
| 23 | 32 | Anonymous | |
| 24 | 39 | Anonymous | h2. [[Laser cutters]] |
| 25 | 1 | jaap | |
| 26 | 38 | bartb | * [[How does a laser cutter work?]] |
| 27 | 32 | Anonymous | * [[HPC LS3020]] |
| 28 | 42 | bartb | * [[Materials and settings]] |
| 29 | 1 | jaap | |
| 30 | 39 | Anonymous | h2. [[Electronics]] |
| 31 | 1 | jaap | |
| 32 | 39 | Anonymous | * [What is the electronics for?] |
| 33 | 32 | Anonymous | * [[LAOS Mainboard v0.3]] |
| 34 | 36 | Anonymous | * [[LAOS I2C Panel v0.3]] |
| 35 | 29 | bartb | |
| 36 | 39 | Anonymous | h2. [[Software]] |
| 37 | 31 | bartb | |
| 38 | 37 | Anonymous | * [[Software overview]] |
| 39 | 39 | Anonymous | * [LAOS firmware] |
| 40 | 45 | Anonymous | * [[LAOS configuration file]] |
| 41 | 40 | jaap | * [[LAOS CUPS driver]] |
| 42 | 33 | Anonymous | * [[VisiCut]] |
| 43 | 28 | bartb | |
| 44 | 51 | Anonymous | h2. Additional information |
| 45 | 1 | jaap | |
| 46 | 51 | Anonymous | * [Historical notes] |
| 47 | 34 | Anonymous | * original wiki - http://wiki.laoslaser.org/index.php/OpensourceLasercutterdriver |