Wiki » History » Version 68
hugomeiland, 2013-02-22 19:11
| 1 | 32 | Anonymous | h1. LAOS Laser |
|---|---|---|---|
| 2 | 1 | jaap | |
| 3 | 32 | Anonymous | {{>toc}} |
| 4 | 1 | jaap | |
| 5 | 32 | Anonymous | !>LaOSLogo.png! |
| 6 | 1 | jaap | |
| 7 | 50 | Anonymous | This site is about an Open Source laser engraver/cutter controller system, both hardware and software. Further info can be found on the [[Rationale and background]] page. The site was created in 2010 by Jaap Vermaas and Peter Brier, and is now being taken further with the help of other [[Contributors]]. |
| 8 | 1 | jaap | |
| 9 | 49 | Anonymous | A laser cutter consists of several components, as described on [[How does a laser cutter work?|this page]] - this site focuses on units such as the [[HPC LS3020]], in combination with the LAOS electronics. For a full list, see the [[Laser Cutters|Supported lasers]] so far. The current electronics are [[LAOS Mainboard v0.3]] and [[LAOS I2C panel v0.3]] - older versions are listed on the [[Electronics]] page. |
| 10 | 1 | jaap | |
| 11 | 61 | jaap | %{color:red}Warning: If you have Rev4 board, read http://redmine.laoslaser.org/issues/68% |
| 12 | |||
| 13 | 52 | Anonymous | > Tip # 1: for quick navigation, see the tabs at the top of each page on this site. |
| 14 | > Tip # 2: click on the section titles below for a list of all the pages related to that section. |
||
| 15 | 1 | jaap | |
| 16 | 46 | Anonymous | h2. [[HowTo's]] |
| 17 | 1 | jaap | |
| 18 | 39 | Anonymous | * [Figure out what you'll need and where to get it] |
| 19 | 41 | Anonymous | * [Prepare your laser cutter for use with LAOS] (including a first firing test) |
| 20 | 56 | jaap | * [[Assembling the LAOS electronics boards]] |
| 21 | 39 | Anonymous | * [Install firmware and verify proper operation] |
| 22 | 44 | Anonymous | * [[Connect the electronics and hook it up to your network]] |
| 23 | 68 | hugomeiland | * [[pwm|Getting PWM to work]] |
| 24 | 41 | Anonymous | * [Install required software on your Windows, Mac, or Linux PC] |
| 25 | 47 | Anonymous | * [[Troubleshooting]] - [Where to get help] - [Contributing to this wiki] |
| 26 | 32 | Anonymous | |
| 27 | 39 | Anonymous | h2. [[Laser cutters]] |
| 28 | 1 | jaap | |
| 29 | 38 | bartb | * [[How does a laser cutter work?]] |
| 30 | 32 | Anonymous | * [[HPC LS3020]] |
| 31 | 60 | darrenp | ** [[Materials_and_settings]] |
| 32 | 58 | darrenp | * [[K40-III]] |
| 33 | 60 | darrenp | ** [[K40-III_Material_settings]] |
| 34 | 57 | bartb | * [[LaOS on the road]] |
| 35 | 54 | peter | * [[A list of users with LAOS converted lasercutters]] |
| 36 | 1 | jaap | |
| 37 | 39 | Anonymous | h2. [[Electronics]] |
| 38 | 1 | jaap | |
| 39 | 53 | peter | * [[What is the electronics for?]] |
| 40 | 32 | Anonymous | * [[LAOS Mainboard v0.3]] |
| 41 | 36 | Anonymous | * [[LAOS I2C Panel v0.3]] |
| 42 | 29 | bartb | |
| 43 | 39 | Anonymous | h2. [[Software]] |
| 44 | 31 | bartb | |
| 45 | 1 | jaap | * [[Software overview]] |
| 46 | 54 | peter | * [[LAOS firmware]] |
| 47 | 45 | Anonymous | * [[LAOS configuration file]] |
| 48 | 62 | jaap | * [[SimpleCode]] (laos gcode file format) |
| 49 | 40 | jaap | * [[LAOS CUPS driver]] |
| 50 | 33 | Anonymous | * [[VisiCut]] |
| 51 | 28 | bartb | |
| 52 | 65 | hugomeiland | h2. [[Future directions]] |
| 53 | 67 | hugomeiland | |
| 54 | 66 | hugomeiland | * [[RTOS]] |
| 55 | 65 | hugomeiland | |
| 56 | 51 | Anonymous | h2. Additional information |
| 57 | 1 | jaap | |
| 58 | 51 | Anonymous | * [Historical notes] |
| 59 | 34 | Anonymous | * original wiki - http://wiki.laoslaser.org/index.php/OpensourceLasercutterdriver |
| 60 | 55 | jaap | * [[Links]] |