Project

General

Profile

Wiki » History » Version 72

hugomeiland, 2013-03-13 23:10

1 32 Anonymous
h1. LAOS Laser
2 1 jaap
3 32 Anonymous
{{>toc}}
4 1 jaap
5 32 Anonymous
!>LaOSLogo.png!
6 1 jaap
7 50 Anonymous
This site is about an Open Source laser engraver/cutter controller system, both hardware and software. Further info can be found on the [[Rationale and background]] page. The site was created in 2010 by Jaap Vermaas and Peter Brier, and is now being taken further with the help of other [[Contributors]].
8 1 jaap
9 49 Anonymous
A laser cutter consists of several components, as described on [[How does a laser cutter work?|this page]] - this site focuses on units such as the [[HPC LS3020]], in combination with the LAOS electronics. For a full list, see the [[Laser Cutters|Supported lasers]] so far. The current electronics are [[LAOS Mainboard v0.3]] and [[LAOS I2C panel v0.3]] - older versions are listed on the [[Electronics]] page.
10 1 jaap
11 61 jaap
%{color:red}Warning: If you have Rev4 board, read http://redmine.laoslaser.org/issues/68%
12
13 70 hugomeiland
14
To avoid confusion, these versions are current:
15
* LAOS Mainboard: v0.4 (with patch)
16
* LAOS I2C panel: v0.3
17
* LAOS firmware: v0.3 (latest bin 9-3-2013)
18
19
20 52 Anonymous
> Tip # 1: for quick navigation, see the tabs at the top of each page on this site.
21
> Tip # 2: click on the section titles below for a list of all the pages related to that section.
22 1 jaap
23 71 hugomeiland
h2. [[Buy a LaosBoard]]
24
25 72 hugomeiland
The [[http://wiki.laoslaser.org/index.php/WebShop|old wiki webshop]] and here is the new [[WebShop]] 
26 71 hugomeiland
27
28 46 Anonymous
h2. [[HowTo's]]
29 1 jaap
30 39 Anonymous
* [Figure out what you'll need and where to get it]
31 41 Anonymous
* [Prepare your laser cutter for use with LAOS] (including a first firing test)
32 56 jaap
* [[Assembling the LAOS electronics boards]]
33 39 Anonymous
* [Install firmware and verify proper operation]
34 44 Anonymous
* [[Connect the electronics and hook it up to your network]]
35 68 hugomeiland
* [[pwm|Getting PWM to work]]
36 41 Anonymous
* [Install required software on your Windows, Mac, or Linux PC]
37 47 Anonymous
* [[Troubleshooting]] - [Where to get help] - [Contributing to this wiki]
38 32 Anonymous
39 39 Anonymous
h2. [[Laser cutters]]
40 1 jaap
41 38 bartb
* [[How does a laser cutter work?]]
42 32 Anonymous
* [[HPC LS3020]]
43 60 darrenp
** [[Materials_and_settings]]
44 58 darrenp
* [[K40-III]]
45 60 darrenp
** [[K40-III_Material_settings]]
46 69 hugomeiland
* [[Lasersaur]]
47 57 bartb
* [[LaOS on the road]]
48 54 peter
* [[A list of users with LAOS converted lasercutters]]
49 1 jaap
50 39 Anonymous
h2. [[Electronics]]
51 1 jaap
52 53 peter
* [[What is the electronics for?]]
53 32 Anonymous
* [[LAOS Mainboard v0.3]]
54 36 Anonymous
* [[LAOS I2C Panel v0.3]]
55 29 bartb
56 39 Anonymous
h2. [[Software]]
57 31 bartb
58 1 jaap
* [[Software overview]]
59 54 peter
* [[LAOS firmware]]
60 45 Anonymous
* [[LAOS configuration file]]
61 62 jaap
* [[SimpleCode]] (laos gcode file format)
62 40 jaap
* [[LAOS CUPS driver]]
63 33 Anonymous
* [[VisiCut]]
64 28 bartb
65 65 hugomeiland
h2. [[Future directions]]
66 67 hugomeiland
67 66 hugomeiland
* [[RTOS]]
68 65 hugomeiland
69 51 Anonymous
h2. Additional information
70 1 jaap
71 51 Anonymous
* [Historical notes]
72 34 Anonymous
* original wiki -  http://wiki.laoslaser.org/index.php/OpensourceLasercutterdriver
73 55 jaap
* [[Links]]